In the current situation of unstable workers, the fully automatic printing machine highlights the great advantage of low labor and stable quality. When there are sufficient workers, 3 people can operate, 1
One person lays the sheet, one person uncovers the sheet, and one person adds the paste. When there is a shortage of workers, the fully automatic printing machine can merge the time spent on peeling into the time spent on laying, so that the laying and peeling are operated at the same end. So this fully automatic oval printing machine can be operated by two people.
The second is that the fully automatic printing machine is extremely energy-efficient. Due to our private server control, the energy-saving and safe whole machine consumes 4.5KW (6 colors as an example). The dryer uses IR type flash drying lamps, which generate electricity for printing as many pieces as possible, and the drying time only takes a few seconds to dry the surface. The number and power of lamps can be freely controlled for different pastes, printing areas, graphics, and other situations. Achieve energy-saving effect and save every penny for the enterprise.
The third is safety and reliability. On the entire printing machine, except for the electricity and machine drying, which are all 380 volts, all other electrical appliances are 24 volts. The standard safe voltage for our human body is 36 volts, and a voltage of 24 volts is absolutely safe for workers. A 380 volt motor can be directly grounded to ensure its safety. In addition, a safety control switch is installed in the corresponding part of the fully automatic printing machine. If the machine exceeds the set range during operation, it will automatically stop until the fault is eliminated before the machine can start and operate normally.
The fourth is the convenience of loading and unloading printing plates. Due to the fact that the manufacturer of the printing machine has absorbed the experience of using the machine from multiple printing factories, they were aware of the printing factory's requirements for the loading and unloading of fully automatic printing plates when manufacturing the machine. They require easy loading and unloading of printing plates without affecting their printing accuracy. Therefore, according to the requirements of the printing factory, the machine adopts the method of positioning the two ends of the printing plate and the upper and lower three points. Like manual plate placement printing, you only need to place the printing plate in a fixed position according to the method set by the machine, and fix the four corners of the printing plate with four bolts. It is also convenient to unload the printing plate. You only need to loosen the four bolts and remove the printing plate. The next time you print, there is no need to re align the plate, making the operation easy.
The fifth is the scraping and ink return of the scraper, and the pressure of the scraper can be adjusted freely. Considering the high investment required to purchase a large fully automatic printing machine, if the pressure of its scraper cannot be adjusted arbitrarily, it can only print coarse line textiles. If it is required to print fine lines, the machine cannot be used or the effect is not good. Therefore, the machine has made significant improvements to the scraper frame and cylinder, and has put in a lot of effort. Now, this fully automatic printing machine can not only make the scraping and ink return of the scraper obvious, but also adjust the pressure of the scraper freely. When printing on textiles with thick lines, we reduce the pressure of the scraper to increase the amount of color leakage. When drawing fine lines, we increase the pressure of the scraper to reduce the amount of color leakage, and the fine lines will appear clearly.
The sixth is that the cutting area is large, making it difficult for one person to manually level it. To address this challenge, a distance of 50 centimeters is left in the middle of the machine, with one person inside and one person outside, for laying large fabric sheets. The simultaneous laying of tiles by two people is not only fast, but also effective.
The seventh is affordable and durable. For the benefit of the printing factory, the materials used for this machine are carefully selected, and most of the components are universal parts of the printing machine. This way, the machine is durable during operation and generally does not require replacement of parts. Normal maintenance can be carried out according to the instructions.
The eighth is convenient maintenance. This fully automatic printing machine adopts PLC control, and most of the components use Swiss ABB modules. The lamp tube is a consumable part (with a warranty of 8000 hours), but it is a branded product that is very convenient to purchase and replace. Overall, whether it is the mechanical or electrical components, their accessories are universal, making it very convenient to repair the machine in case of any malfunction.
Cowint is the largest DTF Film Factory in China
