If we need to achieve the thickness of the hand printed film, we may need to add a solid printing plate. There are two advantages to doing this, one is to save on other looks in the future
The number of scratch marks for color printing; Secondly, if it is a dark fabric printing, the first solid printing plate needs to mix elastic and elastic white for printing, so that other colors of printing can be more beautiful. It is best to use two ovens to quickly dry when implementing this on-site printing.
Foam printing
Foam printing includes three methods: high foam, low foam, and suede foam. These printing techniques are generally combined with other colored adhesive printing techniques. There are three points to note here.
1. The color area of foam printing must be printed on the fabric, and do not print the base color underneath. This is because if foam printing paste is printed on the base paste, its water washing fastness is poor.
2. Foam printing plates should be arranged to be printed after all printing plates as much as possible. This is because if foam is printed in advance during the machine printing process, the foam will be generated very high during the middle drying process, which will affect the printing of other colors. Arranging the final version for printing is also to go through several ovens before picking up the final pieces, so that the foam printing process can be completed in one go, thus saving one foam process.
3. If it is a foam printing with multiple colors, it should be noted that the drying time in the middle should not be too long, and it is best to dry the slurry without starting. Then, after printing the last color, we can initiate it together. In short, when printing foam printing on a machine, the scraping process is particularly uniform and the number of scraping cycles is equal. After the entire batch of products is printed, you will find unexpected results, particularly good consistency before and after, and particularly smooth. This is the advantage of machine printing.
Flocking, hot stamping transfer printing
If we want to achieve one-time printing, hot stamping, flocking and transfer printing on the machine, we also need to configure a pressing machine on the machine. However, in the entire process, flocking or hot stamping paste should be printed first, then dried, followed by flocking hot stamping transfer printing, and finally other color printing. In the process of machine printing, the printing isolation paste is not used, and the flocking, hot stamping and transfer printing process is completed one step ahead of schedule.
Fabric printing with seams
This refers to the semi-finished printing processing in garment factories. For example, at shoulder seams, zippers, and decorative pockets, where multiple layers of stitching are stacked. In general, it is difficult to achieve satisfactory printing results here. Here is a very practical technique introduced. That is to purchase approximately 5mm thick sponge pads from the market and cut them into the size of a tabletop, then use tabletop adhesive to stick them to the tabletop, and then apply tabletop adhesive to form a flexible tabletop. Multi layer stitching can smoothly complete complete the complete flat printing under the pressure of the scraper, with a flat and uniform printing effect, and there will be no stacking phenomenon at high and low places.
Solid heat ink imitates adhesive paste for on-site printing
It is the use of thermosetting ink to create a adhesive film with a solid printing effect. Let's first talk about the film-forming process of thermosetting ink and adhesive printing. The solid content of thermosetting ink is 100%, so it has good covering power and high film thickness. It is formed by the polymerization of PVC resin and plasticizer under the action of temperature. So there must be an external condition, which is heating. This is also a fatal factor limiting its development at present, and it is also the reason why some domestic printing factories are not interested in thermosetting ink (white fabrics will turn yellow when heated, and black fabrics will zoom due to fast heat absorption). However, thermosetting ink printing also has many advantages. It will not clog or crust for a long time, so its utilization rate is very high. Especially in screen printing, its color reproduction rate is unparalleled compared to other coating printing.
The characteristic of adhesive printing is that it is a water-soluble colloid of acrylic resin, which can be naturally dried. It is formed by the evaporation of water and the formation of conjunctiva, with a solid content between 10% and 25%. The conjunctiva is a contractile conjunctiva. So the surface of the conjunctiva obtained after drying is very smooth, but its coverage rate is much lower.
We already know their film-forming process, so how can we achieve thermosetting ink imitation adhesive printing on machines? The first thing we need to do is press and heat the cut piece to be printed before printing. That is to say, after laying the pieces, use a pressing machine to press and flatten the fiber tissue of the cut pieces, and then proceed with printing. The final result is the same as the adhesive printed film, but its performance in all aspects is much better than that of the adhesive, including hand feel, washing fastness, and color reproduction. But its disadvantage is that it cannot be used together with mixed printing processing techniques such as hot stamping and flocking transfer printing.
Cowint is the largest DTF Film Factory in China























